General Description: A Low VOC and Haps, quick drying, high-solids, acrylic enamel developed for agricultural, construction and industrial machinery and small transportation. Our acrylic alkyd enamel series is made without the use of Lead, Zinc Chromate or other toxic heavy metal compunds.
	Common Usage: Typical uses include original equipment machinery and other production line applications. For use where a V.O.C. compliant coating is required in place of present conventional coatings such as Saf-T-Gard or Quick Touch enamels.
	Color: White, Black, Red, Blue (Custom Colors also available)
	Finish: High Gloss

Primer Coats: This product is recommended for use over Anchor LoVoc primer #B-7911 or Low Haps versions #CC-655 and #CC-658. This product is designed to be applied over barrier type primers or intermediate coats. When this is not possible, the coating can be applied directly to clean metal making sure a maximum millage of 2.0 mils dry per coat is applied. Each service environment may require a specific coating system or combination of Anchor products. Consult your Anchor representative for specific job recommendations.

For maximum performance, the recommended substrate should be blasted in accordance with SSPC-SP6 commercial blast. If blast cleaning is not feasible, the substrate should be degreased in accordance with SSPC-SP1. All burrs should be removed and sharp edges or rough weld seams should be ground down. Where weathered steel is applicable and where substrate has reached rust grade, the appropriate chemical cleaning or blasting will be necessary.

	Volume Solids: 52% - Varies By Color
	Recommended Thickness: 1.6-2.0 mils dry per coat. Apply one Tack Coat and then proceed with two full coats
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 50 minutes 30 minutes to 2 hours* (Cooler temperatures and higher humidity will lengthen drying time) * After 2 hours, allow the coating 7 days to cure before additional recoating.
	Architectural and Industrial Maintenance Category: Quick Dry Coatings
	Maximum Allowable V.O.C.: 3.8 lbs./gal. (450 g/l)
	Actual V.O.C.: 3.27lbs./gal. (392 g/l)
	Theoretical Coverage: 830 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails and 1 Gallon cans
	Storage Temperature: Minimum 20 F Maximum 110 F
	Chemical Resistance: Alkalis: Fair Acids: Good Water: Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 3.5 463 Minimum: 1.6 3.1 521 Maximum: 2.0 3.8 417
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: This product is ready-to-spray. Thin with T-50M, a no HAPS solvent, when permitted by federal, state and local regulations.
	Surface Temperature: Minimum 40 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1200-2200 psi. Tip: .011"- .015" Conventional Spray Air Pressure: 60-80 psi Fluid Pressure: 10-20 psi
	Cleanup: Use Anchor #T-50M
	Application Considerations: This material dries very fast. This coating will build much faster than conventional enamels such as Quick Touch. Use caution when applying to avoid excessive film build. Start with a .013" tip orifice and pressures that allow for wet coat without dusting or blow-out. Adjust tip and pressure settings as necessary. Where air quality regulations allow, thin only if necessary up to 15% or until material atomizes at the tip. Apply in wet coats to avoid dusting. When spraying, use a cross-hatch method, overlapping each pass 50%. Clean spray system thoroughly before and after each use. On a derusted surface, the application of a dry film of at least 2.0 mils is recommended.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.