General Description: A durable 100% acrylic water based stain specifically designed for structural concrete.
	Common Usage: This is a quality maintenance coating for commercial traffic on bridges and other concrete applications.
	Color: White and Custom Colors available
	Finish: Semi-Transparent Stain

The surface must be completely dry and free of all contaminants including wax, dirt, oil, grease and loose or failing paint. Test concrete moisture content by taping a sheet of plastic to surface overnight. If moisture is present the next morning, do not paint. New concrete must be completly cured for 28 days before painting. If water beads rather than soaks into the surface, all smooth unpainted concrete should be washed with a non-soapy detergent such as tri-sodium phosphate (T.S.P.) and thoroughly rinsed. Test with litmus paper or a pH pencil to assure a pH of 7-9. If pH is not in range, the surface must be rinsed until a neutral pH is attained.

	Volume Solids: 36% (54% by Weight)
	Recommended Thickness: 1.6-2.0 mils dry per coat. *Two coats recommended for uniform appearance
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 1 Hour 2 Hours (Cooler temperature and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Stains, Clear and Semi-Transparent
	Maximum Allowable V.O.C.: 4.6 lbs./gal. (550 g/l)
	Actual V.O.C.: .16 lbs./gal. (19 g/l) .67 lbs./gal. water + exempt materials
	Theoretical Coverage: 577 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on color, the surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails and 1 Gallon cans
	Storage Temperature: 35 F 110 F
	Physical Properties: Abrasion: Good Flexibility: Excellent Weather: Excellent
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 5.0 321 Minimum: 1.6 4.4 361 Maximum: 2 5.6 289
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water only if necessary up to one pint per gallon.
	Surface Temperature: 50 F 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1800-2400 psi Tip: .015"-.017" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use high quality synthetic or nylon bristle brushes. Roller: Use 1/4"-1 1/4" nap lambswool covers, depending on surface texture.
	Cleanup: Use soap and water.
	Application Considerations: Brush, spray or roll. Strain material before spraying. Back roll after spraying. Check color prior to applying as Anchor cannot be responsible for color dissatisfaction after application. Always apply into rather than away from wet edge, overlapping each pass 50%. Avoid touching up, rolling or brushing back into paint more than ten minutes after applying. Touch up when paint is completly dry. Allow to cure ten days before cleaning newly painted surfaces. Anchor Paint Acrylic Structural Concrete Stain has been evaluated by the chemical unit of the Central Materials Laboratory of the State of Colorado Department of Highways. Our coatings were found to be acceptable for projects using the concrete coatings specified in Section 601 & 708 of the Colorado Department of Highways Structural Concrete Coating Standard.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.