Product Profile:
 |
General Description:
A specially formulated acrylic emulsion that effectively seals off bleeding of
water stains, ink, pencil, smoke and wood tannins.
|
|
Common Usage:
Typically regarded as a general sealer, this product also makes a very
good undercoater for pastels and adheres well over old varnish, lacquer, gloss
finishes, hardboard, etc.
|
|
Color: White |
|
Finish: Flat |
Coating Systems:
|
Finish Coats:
Typical topcoats include latex and oil based enamels. Consult your Anchor
Representative for specific job recommendations.
|
Surface Preparation:
|
All surfaces should be clean, dry, and free of all excess contaminants or old
and failing paint. Surfaces should be cleaned of excess carbon, grease, wax,
etc. with a quality non-soapy detergent. Mildew must be killed using a
solution of chlorine and detergent in water and thoroughly rinsed. Do not use
on chalky surfaces such as old plaster or on surfaces where conditions hinder
the performance of the coating.
|
Technical Data:
|
Volume Solids: 43% |
|
Recommended Thickness: 1.6-2.0 mils dry. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
30 Minutes |
|
1 Hour |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Sealers |
|
Maximum Allowable V.O.C.: 3.3 lbs./gal. (400 g/l) |
|
Actual V.O.C.: .37 lbs./gallon (44 g/l) (.81 lbs./gal. minus water + exempt materials) |
|
Theoretical Coverage:
690 sq. ft./gallon @ 1 mil dry. Coverage will vary depending on the surface
texture, porosity of the surface and the application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
|
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Good |
|
Flexibility: |
|
Good |
|
Weather: |
|
Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
4.2 |
|
383 |
|
Minimum: |
|
1.6 |
|
3.7 |
|
431 |
|
Maximum: |
|
2.0 |
|
4.7 |
|
345 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Do not thin for application.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 90 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1800-2400 psi |
|
Tip: |
|
.013"-.017" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a quality synthetic or nylon bristle brush. |
|
Roller: Use 1/4" lambswool covers. |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
This product can be applied by brush, roller or spray. Apply in one semi-
transparent coat and test for bleeding on a small area with finish coat. Some
stains will require two coats but do not overbuild the coating as the stain is
likely to photograph through. Due to wood tannin variances, some bleeding may
not be stopped.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
