Product Profile:
 |
General Description:
This product is a clear, water soluble silicone that effectively repels water.
|
|
Common Usage:
This product can be used on many above grade exterior vertical surfaces such
as block, brick, stucco, hardboard, siding, and natural stone.
|
|
Color: Clear |
|
Finish: Low Sheen |
Coating Systems:
|
Finish Coats:
Consult your Anchor representative for specific job recommendations.
|
Surface Preparation:
|
The surface must be dry and free of any contaminants that would hinder the
performance such as dirt, oils, excessive efflorescence or chalk, form release
or curing agents and any loose paint by scraping, wire brushing or pressure
washing. Masonry must be cured 28 days. Mold, fungus or mildew must be
removed by applying a solution of one part bleach to three parts water and
thoroughly rinsing. Repair all structural defects such as cracks, breaks or
other flaws prior to application.
|
Technical Data:
|
Volume Solids: 13% |
|
Recommended Thickness: Two wet coats. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
20 Minutes |
|
1 Hour |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Waterproofing and Treatments |
|
Maximum Allowable V.O.C.: 5.0 lbs./gallon (600 g/l) |
|
Actual V.O.C.: Zero |
|
Theoretical Coverage:
209 sq. ft./gallon @ 1 mil dry. Coverage will vary depending on the surface
texture and the application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails and 1 Gallon cans
|
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Flexibility: |
|
Excellent |
|
Water: |
|
Excellent |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.5 |
|
11.5 |
|
139 |
|
Minimum: |
|
1.0 |
|
7.7 |
|
209 |
|
Maximum: |
|
2.0 |
|
15.4 |
|
104 |
|
|
Mixing: Stir thoroughly.
|
|
Thinning: Do not thin for application.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 90 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi. |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a quality synthetic or nylon bristle brush. |
|
Roller: Use 1/4"-1 1/4" nap lambswool covers, depending on surface texture. |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
This product can be applied by brush, roller or spray. Apply two wet-on-wet
coats evenly to surface and avoid runs or overbuilding of the coating.
Coverage will vary between 100-300 sq. ft. per gallon, depending on the
porosity and design of the surface. Expect up to 50% more coverage on the
second coat.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
