Product Profile:
 |
General Description:
A high hiding oil-based primer that flows well, sands easily, and leaves no
brush marks.
|
|
Common Usage:
This primer is typically used for interior cabinets, woodwork, and trim.
|
|
Color: White |
|
Finish: Flat |
Coating Systems:
|
Finish Coats:
Typical topcoats include Anchor #P-300 series, #P-400 series, #P-600 series,
or #P-700 series. Consult your Anchor representative for specific job
recommendations.
|
Surface Preparation:
|
The surface must be free of all dirt, grease, or other contaminants,
loose or failing paint, chalking surfaces, rust or moisture.
|
Technical Data:
|
Volume Solids: 54.43% |
|
Recommended Thickness: 1.6-2.0 mils dry per coat. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
20 Minutes |
|
8 Hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Primers and Undercoaters |
|
Maximum Allowable V.O.C.: 2.9 lbs./gallon (350 g/l) |
|
Actual V.O.C.: 2.8 lbs./gal. (336 g/l) |
|
Theoretical Coverage:
873 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will
vary depending on surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Good |
|
Acids: |
|
Good |
|
Water: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
3.3 |
|
485 |
|
Minimum: |
|
1.6 |
|
2.9 |
|
546 |
|
Maximum: |
|
2.0 |
|
3.7 |
|
437 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Thin only if necessary with Anchor #J-1112.
|
|
Surface Temperature:
| Minimum 40 F |
|
Maximum 90 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi. |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a high quality natural china bristle brush. |
|
Roller: Use a 3/8" or a 1/2" synthetic roller cover |
|
|
Cleanup: Use Anchor #J-1112. |
|
Application Considerations:
This coating allows for brush, roller, or spray application. Always apply into
rather than away from the wet edge, overlapping each pass 50%. Avoid
touching up, rolling or brushing back into paint more than ten minutes after
applying. Touch up when paint is completely dry. Allow the paint to cure at
least ten days before cleaning newly painted surfaces.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
