General Description: A pure 100% acrylic water soluble enamel providing an attractive and durable coating. Unlike conventional oil enamels, this coating will not prematurely lose gloss, flexibility, or color retention with age.
	Common Usage: This is a scrubbable semi-gloss finish that can be used in kitchens, baths, schools, motels, apartments, or any non-metallic surface which requires resistance to marring, stains, scuffing, etc.
	Color: White, Standard and Custom colors
	Finish: Semi-Gloss

Primer Coats: Interior Woodwork: Use Anchor #P-1507 Alkyd Undercoater, Interior Walls: #P-1508 Latex Drywall Sealer, Exterior: 3601 Latex Primer. Consult your Anchor representative for specific job recommendations.

All surfaces must be clean, dry, and free of any contaminants or conditions of the surface that would hinder the performance of the coating such as dirt, grease, wax, stains, and glossy finishes.

	Volume Solids: 27.98% -varies by color
	Recommended Thickness: 1.6-2.0 mils dry per coat.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 2 Hours 8 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Non-Flat Coatings
	Maximum Allowable V.O.C.: 3.2 lbs./gal. (380g/l)
	Actual V.O.C.: 60 lbs./gal. (72 g/l) (1.75 lbs./gal. minus water + exempt materials) - varies by color
	Theoretical Coverage: 447 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Very Good Flexibility: Good Weather: Very Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 4.4 364 Minimum: 1.6 3.9 410 Maximum: 2.0 4.9 328
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water only if necessary up to one pint per gallon.
	Surface Temperature: Minimum 50 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1800-2400 psi Tip: .013"-.017" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use high quality synthetic or nylon bristle brushes. Roller: Use appropriate nap lambswool covers.
	Cleanup: Use soap and water.
	Application Considerations: This coating allows for brush, roller, or spray application. Check color before applying as Anchor can not be responsible for color dissatisfaction after application. Always apply into rather than away from the wet edge, overlapping each pass 50%. Avoid touching up, rolling or brushing back into paint more than ten minutes after applying. Touch up when paint is completely dry. Allow the paint to cure at least ten days before cleaning newly painted surfaces.
	Touch Up: Proper touch-up is accomplished by applying a thin coat of this product over a well coated surface using the same method of application as used to apply the finish coat, that is, spray over spray, roller over roller. If the finish coat is sprayed, it is also possible to spray a small amount into an empty container, then touching up with a foam brush. Touch up should be done within 5 degrees of the original temperature.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.