General Description: This quality latex product comes ready to use. No primer or sealer is normally necessary. It will not yellow, dries fast, cleans up with soap and water, and is low odor.
	Common Usage: A specially formulated vinyl-acrylic emulsion for wall board, plaster, wood, block, and other interior surfaces.
	Color: White, Standard and Custom colors
	Finish: Flat

Primer Coats: Some applications might need Anchor #P-1508 drywall sealer, however on new surfaces, normally two coats of #P-100 series will be sufficient. Consult your Anchor representative for specific job recommendations.

The surface must be clean, dry, and free of any contaminants. On previously painted surfaces, be sure that stains and imperfections will not bleed through coating. New or old surfaces need not be primed unless variance in color is substantial. Glossy surfaces should be sanded or flattened by use of a chemical deglosser.

	Volume Solids: 33.7% -varies by color
	Recommended Thickness: 1.6-2.0 mils dry per coat.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 20 Minutes 1 Hour (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Flat Coatings, Interior
	Maximum Allowable V.O.C.: 2.1 lbs./gal. (250g/l)
	Actual V.O.C.: .42 lbs./gal. (50 g/l), (1.09 lbs./gal. minus water + exempt materials) - varies by color
	Theoretical Coverage: 541 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans.
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Good Flexibility: Good Weather: Interior Use Only
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 5.3 300 Minimum: 1.6 4.7 338 Maximum: 2.0 5.9 270
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water only if necessary up to one pint per gallon.
	Surface Temperature: Minimum 50 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1800-2400 psi Tip: .015"-.017" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use high quality synthetic or nylon bristle brushes. Roller: Use 1/4"-1 1/4" nap lambswool covers, depending on surface texture.
	Cleanup: Use soap and water.
	Application Considerations: This coating allows for brush, roller, or spray application. Check color before applying as Anchor can not be responsible for color dissatisfaction after application. Always apply into rather than away from the wet edge, overlapping each pass 50%. Avoid touching up, rolling or brushing back into paint more than ten minutes after applying. Touch up when paint is completely dry. Allow the paint to cure at least ten days before cleaning newly painted surfaces.
	Touch Up: Proper touch-up is accomplished by applying a thin coat of this product over a well coated surface using the same method of application as used to apply the finish coat, that is, spray over spray, roller over roller. If the finish coat is sprayed, it is also possible to spray a small amount into an empty container, then touching up with a foam brush. Touch up should be done within 5 degrees of the original temperature.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.