Product Profile:
 |
General Description:
A high gloss, oil based enamel for interior and exterior use.
|
|
Common Usage:
This is an excellent all-purpose coating that can be applied to wood or ferrous
metals. It has very good results on motors, woodwork, lawn furniture,
handrails, etc.
|
|
Color: White, Standard and Custom colors. |
|
Finish: High Gloss |
Coating Systems:
|
Primer Coats:
Use Anchor #P-1507 Undercoater for wood, #1600 Series Rust Inhibitive Primer
for steel. Consult your Anchor representative for specific job requirements.
|
Surface Preparation:
|
Interior: The surface must be free of all dirt, grease, or other contaminants,
loose or failing paint, chalking surfaces, rust or moisture. Glossy surfaces
should be dulled with sandpaper or chemical deglossers. Mildew should be
removed by applying a mixture of chlorine into a solution of water and
detergent.
Exterior: the substrate should be thoroughly degreased in accordance with
SSPC-SP1. All burrs should be removed and sharp edges or rough weld
seams should be ground down. Where weathered steel is applicable and
where the substrate has reached rust grade, appropriate chemical cleaning or
blasting will be necessary.
|
Technical Data:
|
Volume Solids: 54.14% -varies by color |
|
Recommended Thickness: 1.6-2.0 mils dry per coat. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
2 Hours |
|
8 Hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Non-Flat Coatings, Exterior |
|
Maximum Allowable V.O.C.: 3.2 lbs./gallon (380g/l) |
|
Actual V.O.C.: 3.02 lbs./gal. (362 g/l) -varies by color |
|
Theoretical Coverage:
868 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will
vary depending on color, surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Very Good |
|
Flexibility: |
|
Good |
|
Weather: |
|
Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
3.3 |
|
482 |
|
Minimum: |
|
1.6 |
|
2.9 |
|
543 |
|
Maximum: |
|
2.0 |
|
3.7 |
|
434 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Use Anchor #J-1112.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi. |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a high quality natural china bristle brush. |
|
Roller: Use a 3/8" or a 1/2" synthetic roller cover |
|
|
Cleanup: Use Anchor #J-1112. |
|
Application Considerations:
This coating allows for brush, roller, or spray application. Apply in wet coats
to assure a smooth, even finish. When applying, use cross-hatch method,
overlapping each pass 50%. Clean system thoroughly before and after each
use. On a derusted surface the application of a dry film thickness of at least
2 mils is recommended.
|
|
Touch Up:
Proper touch-up is accomplished by applying a thin coat of this product over a
well coated surface using the same method of application as used to apply
the finish coat, that is, spray over spray, roller over roller. If the finish coat is
sprayed, it is also possible to spray a small amount into an empty container,
then touching up with a foam brush. Touch up should be done within 5
degrees of the original temperature.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
