Product Profile:
 |
General Description:
A low V.O.C. single component organic zinc rich primer.
|
|
Common Usage:
Applicable on properly prepared steel surfaces or for touch-up on welded or
riveted areas.
|
|
Color: Gray |
|
Finish: Flat |
Coating Systems:
|
Finish Coats:
Suitable topcoats include alkyds, modified alkyds, waterbornes and epoxies
with proper intermediate coat. Do not apply epoxies, vinyls, or other
coatings containing strong strong solvents such as aromatics or ketones
directly on this coating . Each service environment may require a specific
coating system or combination of Anchor products. Consult your Anchor
representative for specific job recommendations.
|
Surface Preparation:
|
Under no circumstances should this material be applied over oily or greasy
surfaces. At minimum, cleaning should be accomplished by mechanical
hand cleaning to meet SSPC-SP1 or light sandblasting to meet SSPC-SP7.
Sandblasting will not clean oil and grease. Do not clean oily surfaces with
thinner as this will merely smear the oil. A detergent wash and thorough
rinse is necessary to properly remove dirt and oil.
|
Technical Data:
|
Volume Solids: 53.14% |
|
Recommended Thickness: 1.8-2.4 mils minimum dry. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
2 Hours |
|
24 Hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Metallic Pigmented |
|
Maximum Allowable V.O.C.: 4.2 lbs./gal. (500 g/l) |
|
Actual V.O.C.: 3.08 lbs./gal. (370 g/l) |
|
Theoretical Coverage:
853 sq. ft./ gallon @ 1 mil dry, assuming no application loss. Coverage will
vary depending on surface texture and application technique.
|
|
Packaging: 5 Gallon pails and 1 Gallon cans.
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Poor |
|
Acids: |
|
Poor |
|
Water: |
|
Excellent2. |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
2.1 |
|
4.2 |
|
406 |
|
Minimum: |
|
1.8 |
|
3.9 |
|
474 |
|
Maximum: |
|
2.4 |
|
4.5 |
|
355 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: This coating is V.O.C. compliant, thin only if necessary with Anchor #J-1131
for spray applications or #J-1112 for brush or roller if permitted by federal,
state, and local regulations.
|
|
Surface Temperature:
| Minimum 40 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
2100-3000 psi. |
|
Tip: |
|
.017"-.023" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-60 psi |
|
|
Fluid Pressure: |
|
10-20 psi |
|
|
Cleanup: Use Anchor #J-1131 synthetic thinner. |
|
Application Considerations:
Ensure that the coating is uniformly applied with particular care afforded to
edges, angles, and corners. On a derusted surface, the application of a dry
film thickness of at least 2 mils is recommended. With any oxidative coating,
faster dry time may be obtained with incresed air movement and/or higher
substrate or material temperature. Coverage will vary depending on surface
texture and application technique.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
