General Description: A premium acrylic emulsion coating formulated for use on galvanized antenna towers. The alkalinity of the vehicle will etch into the zinc unlike ordinary enamels and form a chemical bond. This product dries quickly and has excellent weathering properties.
	Common Usage: This product is specifically designed for use on galvanized antenna towers. It meets Federal Standard 595 color #17875 White and color #12197 Orange. Also complies with national Bureau of Standards report NBS1R75-663 and F.A.A. A/C70/7460-1H. Consult your Anchor representative for specific job recommendations.
	Color: Aviation White and Orange
	Finish: Gloss

Primer Coats: In-service towers: Spot prime rust areas with Anchor #2722 Red Rust Inhibitive water-borne primer. New Galvanize: Self-Priming or #2722 Series for maximum performance.

New Galvanize: Must be dry. Clean all oil, grease, or other contaminants in accordance with SSPC-SP1 standards. For maximum performance and when feasible, if spangle is present it is recommended to brush blast to gray galvanize or etch with hydrochloric acid until weathered gray appearance is reached. Follow with clear water rinse until surface is free of blast or etch residue. Note: when blasting or etching use caution to avoid removing excess zinc metal. Existing Towers: Must be dry. Spot prime all rusted areas and remove any contaminants including chalk, dirt, grease, failing paint, etc. Prior to application, prepare substrate in accordance with SSPC-SP1 standards. On unpainted surfaces, clean contaminants such as dirt, white Zinc oxide, etc. and spot prime rusted areas.

	Volume Solids: 34% - varies by color.
	Recommended Thickness: 3 mils dry, minimum.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 1 Hour 3 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Antenna Coatings
	Maximum Allowable V.O.C.: 4.4 lbs./gal. (530g/l)
	Actual V.O.C.: .68 lbs./gal. (82g/l) (1.62 lbs./gal. minus water + exempt materials)
	Theoretical Coverage: 545 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on the color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, and 1 Gallon cans
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Very Good Flexibility: Very Good Weather: Very Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 4.0 11.8 136 Minimum: 3.0 8.8 182 Maximum: 5.0 14.7 109
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water only if necessary up to one pint per gallon.
	Surface Temperature: Minimum 50 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1800-2400 psi Tip: .015"-.017" Conventional Spray Air Pressure: 40-70 psi Fluid Pressure: 10-20 psi Brush: Use high quality synthetic or nylon bristle brushes. Roller: Use 1/4" lambswool covers.
	Cleanup: Use soap and water.
	Application Considerations: Apply by brush, mitt, roller, or spray. When the temperature is above 90 F make sure that full wet coats are applied, overlapping each pass 50% to avoid dusting. Material can freeze. Avoid applying when overnight freeze or rain is possible. Coverage will vary depending on surface texture, equipment in use, application methods, and experience of the applicator.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.