Product Profile:
 |
General Description:
This is a quick drying short oil alkyd enamel. It is an excellent enamel
characterized by high durability, gloss retention and color retention.
|
|
Common Usage:
Equipment or production line needs where rapid drying is a must. This
product can be used as a D.T.M. (Direct to Metal) coating although the
use of a primer increases durability.
|
|
Color: White, Standard and Custom colors. |
|
Finish: High Gloss |
Coating Systems:
|
Primer Coats:
Use Anchor #472 Gray, #2655 White, #2653 Red Fast Dry Primers. Consult
your Anchor representative for specific job recommendations.
|
Surface Preparation:
|
The faster dry the material, the better cleaning required. The substrate should be
cleaned in accordance with SSPC-SP1. All burrs should be removed and sharp
edges or rough weld seams should be ground down. Where weathered steel is
applicable and where the substrate has reached rust grade, appropriate
chemical cleaning or blasting will be necessary. This product is designed to
applied over a barrier primer or intermediate coats. When not feasible, this
product can be applied directly over the substrate making sure a maximum
millage is achieved.
|
Technical Data:
|
Volume Solids: 34.39% -varies by color |
|
Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
15 Minutes |
|
40 Minutes |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Not Intended for Residential Use, Shop Use Only. |
|
Actual V.O.C.: 4.5 lbs./gal. (540g/l) -varies by color |
|
Theoretical Coverage:
552 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will
vary on color, surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans |
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Fair |
|
Acids: |
|
Good |
|
Water: |
|
Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
5.2 |
|
306 |
|
Minimum: |
|
1.6 |
|
4.6 |
|
345 |
|
Maximum: |
|
2.0 |
|
5.8 |
|
275 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can. |
|
Thinning: Use Anchor #J-1131 or #J-34 Fine Finish Blend. |
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%. |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi |
|
|
Fluid Pressure: |
|
10-20 psi |
|
|
Cleanup: Use Anchor #J-1131 or #J-34 Fine Finish Blend. |
|
Application Considerations:
Spray application only. Apply in wet coats to avoid dusting. When spraying, use
cross-hatch method, overlapping each pass 50%. Clean system thoroughly
before and after each use. On a derusted surface the application of a dry film
thickness of at least 2 mils is recommended.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
