General Description: All heat resistant finishes manufactured by Anchor Paint are formulated with a pure silicone resin modified with an acrylic to provide room temperature drying. The pure silicones are the only resins known that will withstand the shock of being immediately hot then cold. Hi-Temp silicones air dry rapidly, but remain soft until heat cured.
	Common Usage: This product is typically used on smokestacks, furnaces, pipes, etc. where temperature ranges from 450 F to 1200 F.
	Color: Aluminum
	Finish: Metallic

Primer Coats: Cat-0-Zinc 55 up to 600 F or 93 up to 750 F; or direct to blast cleaned metal for maximum temperature resistance. Consult your Anchor representative for specific job recommendations.

Note: Maximum temperature resistance will require maximum surface preparation in accordance with SSPC-SP6 and direct to metal application. For temperatures less than maximum, appropriate cleaning for the level desired and primer selected will be necessary (refer to applicable primer data sheet for details). If the surface preperation given here is not feasible, mechanical and hand clean in accordance with SSPC-SP2; however, less than optimum performance should be expected. The surface must be dry and free of all dirt, grease, oil, or other foreign matter as well as failing paint and rust.

	Volume Solids: 27.94%
	Recommended Thickness: 1.0-1.5 mils dry per coat.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 20 minutes Overnight or bake @ 350 F for 2 Hours (Cooler temperatures and higher humiidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: High Temperature Coatings
	Maximum Allowable V.O.C.: 5.4 lbs./gal (650 g/l)
	Actual V.O.C.: 5.06 lbs./gal. (607.2 g/l)
	Theoretical Coverage: 448 sq. ft./ gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on the surface texture and application technique.
	Packaging: 5 Gallon pails and 1 Gallon cans
	Storage Temperature: Minimum 20 F Maximum 110 F
	Chemical Resistance: Alkalis: Fair Acids: Fair
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.25 4.5 359 Minimum: 1.0 3.6 448 Maximum: 1.5 5.4 299
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Use Anchor #J-1131 thinner.
	Surface Temperature: Minimum 40 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1200-2200 psi Tip: 011"-.015" Conventional Spray Air Pressure: 60-80 psi Fluid Pressure: 10-20 psi. Brush: Use high quality natural china bristle brushes. Roller: Use 1/4" synthetic nap covers.
	Cleanup: Use Anchor #J-1131 synthetic thinner.
	Application Considerations: Spray preferred, brushing and roller compromises the aesthetics of the finish. Touch up using same method as original application. Best if field applied at site of service due to soft nature of coating prior to heat curing. Requires heat curing for maximum durability and heat resistance to contaminants and weather. Normally allow coating to air dry for one hour prior to baking for two hours @ 350 F. Apply in wet coats, overlapping each pass 50%.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.