General Description: A quick-drying, high solids, acrylic alkyd enamel developed for industrial applications.
	Common Usage: Typical uses include heavy equipment, machinery, fabricated steel and as a general maintenance coating. This is a V.O.C. compliant coating that offers superior gloss, coverage, hardness, and a fast cure time compared to conventional heavy duty enamels.
	Color: White, Standard and Custom colors
	Finish: High Gloss

Primer Coats: Low V.O.C. primers, Anchor #B-7911, #CC-54 or other barrier type primers for best performance. LoVoc may be applied directly to metal over properly prepared steel surfaces. Consult your Anchor representative for specific job recommendations.

The surface substrate should be cleaned in accordance with SSPC-SP6 commercial blast. If this is not feasible, then clean to SSPC-SP1 standards. All burrs should be ground down. Where weathered steel is applicable and where the substrate has reached rust grade, an appropriate chemical cleaning or blasting will be necessary. This product is designed to be applied over barrier type primers or intermediate coats. When this is not feasible, the coating can be directly applied to clean metal making sure a maximum millage of 2 mils dry per coat is achieved.

	Volume Solids: 56.52% -varies by color
	Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 45 Minutes 2 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Quick Dry Coatings
	Maximum Allowable V.O.C.: 3.8 lbs./gal. (450 g/l)
	Actual V.O.C.: 3.1 lbs./gal. (372 g/l)
	Theoretical Coverage: 904 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
	Storage Temperature: Minimum 20 F Maximum 110 F
	Chemical Resistance: Alkalis: Fair Acids: Good Water: Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 3.1 502 Minimum: 1.6 2.8 565 Maximum: 2.0 3.5 452
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: This coating is V.O.C. compliant, thin only if necessary with Anchor #J-34 or #J-22M if permitted by federal, state, and local regulations.
	Surface Temperature: Minimum 40 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray This material dries very fast. Use small to medium size fine finish tips and pressures that allow for wet coat without excessive overspray or dusting. The use of a fine finish tip may improve results. Pressure: 1200-2200 psi. Tip: .011"-.015" Conventional Spray Air Pressure: 60-80 psi. Fluid Pressure: 10-20 psi.
	Cleanup: Use Anchor #J-34 or #J-22M synthetic thinner.
	Application Considerations: Note: This finish will build much faster than conventional enamel such as #1200 Quick Touch Enamel. Use caution when applying to avoid excessive film build. Apply in wet coats to avoid dusting. When spraying, use a cross- hatch method, overlapping each pass 50%. Clean spray system throughout before and after each use. Do not apply when the temperature is within 5% degrees F of the dewpoint. On a derusted surface, the application of a dry film thickness of at least 2 mils is recommended.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.