Product Profile:
 |
General Description:
A fast drying thermo-plastic acrylic aluminum.
|
|
Common Usage:
Shop applications where the overspray or fallout of paint particles would
normally get on objects not intended. Spray particles will dry within 15 ft.
under normal conditions.
|
|
Color: Aluminum |
|
Finish: Metallic |
Coating Systems:
|
Primer Coats:
Self-Priming. Consult your Anchor representative for specific job recommendations.
|
Surface Preparation:
|
Remove all rust, dirt, grease, oil, or other contaminants in accordance with
SSPC-SP1. Loose or failing paint should be removed by a light blast or
power tool cleaning. Secured existing paint should be checked for
compatability by applying the coating in a small area, allowing to cure, and
cutting the coating to check for lifting and adhesion between coats.
|
Technical Data:
|
Volume Solids: 28.21% |
|
Recommended Thickness: 1.0-1.5 mils dry per coat. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
5 minutes |
|
20 minutes |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Not Intended for Residential Use; Shop Use Only |
|
Actual V.O.C.: 5.13 lbs./gal. (615 g/l) |
|
Theoretical Coverage:
452 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on surface texture and application technique.
|
|
Packaging: 5 Gallon pails and 1 Gallon cans |
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Excellent |
|
Acids: |
|
Excellent |
|
Water: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.25 |
|
4.4 |
|
362 |
|
Minimum: |
|
1.0 |
|
3.5 |
|
453 |
|
Maximum: |
|
1.5 |
|
5.3 |
|
301 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can. |
|
Thinning: Use Anchor #J-1131 synthetic thinner. |
|
Surface Temperature:
| Minimum 40 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%. |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi |
|
|
Fluid Pressure: |
|
10-20 psi. |
|
|
Cleanup: Use Anchor #J-1131 synthetic thinner. |
|
Application Considerations:
Spray application only. In extra warm temperatures, avoid dusting by
applicating in full wet coats. On rusting areas, spot prime and build finish to a
minimum of 2 mils dry.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
